In this article
Short answer
The ASUS Dual GeForce RTX 5060 Ti 16GB is the best all-round GPU for AI video upscaling. Puget Systems found it the only entry-level card in its Topaz Video test compatible with every Starlight model, and its 16 GB of memory suits current models. The RTX 5070 is faster on NVIDIA's side.
- Memory size decides which upscaling models a card can run.
- Puget found the RTX 5070 does not meet the requirements of some Starlight models.
- The RX 9070 XT leads on several models but managed 1.37 fps on Proteus Natural 2X.
- Check your software's models first, because the ranking changes with the model.
- Best overallASUS Dual GeForce RTX 5060 Ti 16GB GDDR7 OC
- Best for NVIDIA speed at 12 GBASUS Dual GeForce RTX 5070 12GB GDDR7 OC Edition
- Best for speed on supported modelsPowerColor Reaper Radeon RX 9070 XT 16GB GDDR6
Comparison at a glance#
| Model | VRAM | Memory type | Board power | Recommended PSU |
|---|---|---|---|---|
| ASUS Dual GeForce RTX 5060 Ti 16GB GDDR7 OC | 16 GB | GDDR7 | 180 W | 550 W |
| ASUS Dual GeForce RTX 5070 12GB GDDR7 OC Edition | 12 GB | GDDR7 | 250 W | 750 W |
| PowerColor Reaper Radeon RX 9070 XT 16GB GDDR6 | 16 GB | GDDR6 | 304 W | 750 W |
How we picked#
The picks combine specifications from the board makers and the chip makers with the Topaz Video results Puget Systems published for consumer GPUs. Puget ran Topaz Video's internal benchmark on each model and reports frames per second. Puget tested reference or other brand cards, not the exact partner cards listed here, and the notes under each chart say so. Memory size and software compatibility came first, then measured speed, then board power.
The picks#
ASUS Dual GeForce RTX 5060 Ti 16GB GDDR7 OC
ASUS- VRAM16 GB
- MemoryGDDR7
- Power180 W
- PSU550 W
This is the pick for most upscaling work. ASUS lists 16 GB of GDDR7 on a 128-bit interface, a 2.5-slot cooler measuring 229 x 120 x 50 mm and a single 8-pin power connector. The RTX 5060 Ti draws 180 W at its reference rating, per NVIDIA, and ASUS recommends a 550 W power supply. ASUS lists an AI performance figure of 759 TOPS.
Puget Systems found the 16 GB RTX 5060 Ti the only entry-level card in its Topaz Video test that is compatible with every Starlight model. That matters because Topaz's newer models carry higher memory demands, and Topaz says several models need 8 GB or more. Puget measured the RTX 5070 as 32% faster than the RTX 5060 Ti on its Overall score, so you give up some speed for compatibility.
For an Indian buyer, the practical points are the modest power connector and the 550 W power supply recommendation, which suit many existing PCs. Check the exact model name before ordering.
| Spec | Detail |
|---|---|
| GPU | NVIDIA GeForce RTX 5060 Ti |
| Memory size (VRAM) | 16 GB |
| Memory type | GDDR7 |
| Total board power | 180 W |
| Recommended PSU | 550 W |
| Power connector | 1 x 8-pin |
| Outputs | 1 x HDMI 2.1b, 3 x DisplayPort 2.1b |
Pros
- 16 GB of memory, the amount Puget found compatible with every Starlight model
- Single 8-pin connector and a 550 W power supply recommendation from ASUS
- Lowest board power of the three at 180 W
Cons
- The RTX 5070 is 32% faster on Puget's Overall score
- 128-bit memory interface
Best for upscaling with the full range of Topaz models on a modest power supply
Not for users who want the fastest NVIDIA speed on older models
Sources: Maker: asus.com (opens in a new tab), Maker: nvidia.com (opens in a new tab), Benchmark: pugetsystems.com (opens in a new tab)
ASUS Dual GeForce RTX 5070 12GB GDDR7 OC Edition
ASUS- VRAM12 GB
- MemoryGDDR7
- Power250 W
- PSU750 W
The RTX 5070 is the speed pick on the NVIDIA side. ASUS lists 12 GB of GDDR7 on a 192-bit interface, a 2.53-slot cooler measuring 249 x 126 x 50.6 mm, a 16-pin power connector and a 750 W power supply recommendation. NVIDIA rates the reference RTX 5070 at 250 W. ASUS lists 988 TOPS of AI performance.
Puget Systems called it the fastest of the entry-level cards it tested, ahead of the RTX 5060 Ti and the Arc B580. It measured the RTX 5070 nearly 50% faster than the Arc B580 and 32% faster than the RTX 5060 Ti on its Overall score. The catch is memory: Puget notes the RTX 5070 does not meet the system requirements for the Starlight Fast 2 and Starlight Sharp models in Topaz Video. If your workflow uses those models, the 12 GB limit matters more than the speed.
NVIDIA lists a 650 W required system power for its reference RTX 5070, while ASUS recommends a 750 W power supply for this card. Follow ASUS for this model.
| Spec | Detail |
|---|---|
| GPU | NVIDIA GeForce RTX 5070 |
| Memory size (VRAM) | 12 GB |
| Memory type | GDDR7 |
| Total board power | 250 W |
| Recommended PSU | 750 W |
| Power connector | 1 x 16-pin |
| Outputs | 1 x HDMI 2.1b, 3 x DisplayPort 2.1b |
Pros
- Fastest of Puget's entry-level cards in Topaz Video
- GDDR7 memory on a 192-bit interface
- Compact 2.53-slot Dual cooler
Cons
- 12 GB does not meet the requirements of some newer Starlight models, per Puget
- Needs a 16-pin connector and a 750 W power supply recommendation
Best for upscaling with Artemis, Iris and Proteus models where speed matters most on NVIDIA
Not for workflows built on the newest memory-heavy models
Sources: Maker: asus.com (opens in a new tab), Maker: nvidia.com (opens in a new tab), Benchmark: pugetsystems.com (opens in a new tab)
PowerColor Reaper Radeon RX 9070 XT 16GB GDDR6
PowerColor- VRAM16 GB
- MemoryGDDR6
- Power304 W
- PSU750 W
The RX 9070 XT is the fastest card in this guide on several models, and the least flexible. PowerColor lists 16 GB of GDDR6 on a 256-bit interface, two 8-pin connectors and a 304 x 127 x 42 mm cooler. AMD lists a 304 W typical board power, and PowerColor gives 750 W as the minimum system power.
In Puget's charts it leads on Artemis, Iris and Proteus. It then falls away badly on Proteus Natural 2X, where Puget reports 1.37 fps against 19.17 fps for the RTX 5090. Puget also notes the card is compatible only with Starlight Precise 2.5 for local processing, and it reports the RTX 5070 Ti 7% faster and the RTX 5080 18% faster than the card on its Overall score. In short, the speed depends heavily on the model you choose.
Stock is the other point.
| Spec | Detail |
|---|---|
| GPU | AMD Radeon RX 9070 XT |
| Memory size (VRAM) | 16 GB |
| Memory type | GDDR6 |
| Total board power | 304 W |
| Recommended PSU | 750 W |
| Power connector | Two 8-pin |
| Outputs | 1 x HDMI 2.1b, 3 x DisplayPort 2.1a |
Pros
- Highest frame rates of the three on Artemis, Iris and Proteus in Puget's results
- 16 GB of memory on a 256-bit interface
- Two standard 8-pin connectors
Cons
- Proteus Natural 2X ran at 1.37 fps in Puget's test
- Compatible only with Starlight Precise 2.5 for local processing, per Puget
- Highest board power of the three at 304 W
Best for upscaling with Artemis, Iris or Proteus models where raw speed counts
Not for users who rely on Proteus Natural or the wider Starlight range
Sources: Maker: powercolor.com (opens in a new tab), Maker: amd.com (opens in a new tab), Benchmark: pugetsystems.com (opens in a new tab)
Performance and benchmarks#
Puget Systems published Topaz Video's internal benchmark for consumer GPUs. It ran each model at 1080p on a Threadripper PRO platform with Windows 11. Puget tested a reference RTX 5070, a PNY RTX 5060 Ti 16 GB and a Sapphire RX 9070 XT, so the figures below describe the chips and not the exact partner cards named in this guide. Higher is better.
Topaz Video 1.6.1 internal benchmark, Artemis 1X model, 1920x1080: Processing speed (fps, higher is better)
3 products. Highest: PowerColor Reaper Radeon RX 9070 XT 16GB GDDR6, 33.55 fps. Lowest: ASUS Dual GeForce RTX 5060 Ti 16GB GDDR7 OC Edition, 16.7 fps.
| Product | fps |
|---|---|
| PowerColor Reaper Radeon RX 9070 XT 16GB GDDR6 | 33.55 |
| ASUS Dual GeForce RTX 5070 12GB GDDR7 OC Edition | 25.96 |
| ASUS Dual GeForce RTX 5060 Ti 16GB GDDR7 OC Edition | 16.7 |
About this data: figures are copied from the named source, not measured by us, and the test system and settings are those the source states above. See all benchmark sources and credits.
On the Artemis 1X model, the RX 9070 XT leads with 33.55 fps, followed by the RTX 5070 at 25.96 fps and the RTX 5060 Ti at 16.7 fps.
Topaz Video 1.6.1 internal benchmark, Iris 2X model, 1920x1080: Processing speed (fps, higher is better)
3 products. Highest: PowerColor Reaper Radeon RX 9070 XT 16GB GDDR6, 24.2 fps. Lowest: ASUS Dual GeForce RTX 5060 Ti 16GB GDDR7 OC Edition, 11.98 fps.
| Product | fps |
|---|---|
| PowerColor Reaper Radeon RX 9070 XT 16GB GDDR6 | 24.2 |
| ASUS Dual GeForce RTX 5070 12GB GDDR7 OC Edition | 17.69 |
| ASUS Dual GeForce RTX 5060 Ti 16GB GDDR7 OC Edition | 11.98 |
About this data: figures are copied from the named source, not measured by us, and the test system and settings are those the source states above. See all benchmark sources and credits.
The Iris 2X model shows the same order, with 24.2, 17.69 and 11.98 fps. The AMD card keeps its lead.
Topaz Video 1.6.1 internal benchmark, Proteus 2X model, 1920x1080: Processing speed (fps, higher is better)
3 products. Highest: PowerColor Reaper Radeon RX 9070 XT 16GB GDDR6, 25.58 fps. Lowest: ASUS Dual GeForce RTX 5060 Ti 16GB GDDR7 OC Edition, 13.38 fps.
| Product | fps |
|---|---|
| PowerColor Reaper Radeon RX 9070 XT 16GB GDDR6 | 25.58 |
| ASUS Dual GeForce RTX 5070 12GB GDDR7 OC Edition | 19.66 |
| ASUS Dual GeForce RTX 5060 Ti 16GB GDDR7 OC Edition | 13.38 |
About this data: figures are copied from the named source, not measured by us, and the test system and settings are those the source states above. See all benchmark sources and credits.
On Proteus 2X, the three cards reach 25.58, 19.66 and 13.38 fps in the same order.
Topaz Video 1.6.1 internal benchmark, Proteus Natural 2X model, 1920x1080: Processing speed (fps, higher is better)
3 products. Highest: ASUS Dual GeForce RTX 5070 12GB GDDR7 OC Edition, 6.8 fps. Lowest: PowerColor Reaper Radeon RX 9070 XT 16GB GDDR6, 1.37 fps.
| Product | fps |
|---|---|
| ASUS Dual GeForce RTX 5070 12GB GDDR7 OC Edition | 6.8 |
| ASUS Dual GeForce RTX 5060 Ti 16GB GDDR7 OC Edition | 4.96 |
| PowerColor Reaper Radeon RX 9070 XT 16GB GDDR6 | 1.37 |
About this data: figures are copied from the named source, not measured by us, and the test system and settings are those the source states above. See all benchmark sources and credits.
Proteus Natural 2X changes the picture. The RTX 5070 leads with 6.8 fps and the RTX 5060 Ti follows with 4.96 fps, while the RX 9070 XT manages only 1.37 fps. The lesson is that a card's rank can flip with the model, so check which Topaz models you use. Puget also says Topaz Video is mainly GPU-intensive, so a consumer CPU is still suitable.
Puget also reports the RTX 5090 21% faster than the RTX 5080 on its Overall score. Those larger cards are covered in our GPU guides.
Value for money#
Value here follows memory and measured throughput. The RTX 5060 Ti 16GB gives 16 GB of memory at the lowest board power of the three, and it was the only entry-level card Puget found compatible with every Starlight model. The RTX 5070 gives up memory for speed, running 32% faster on Puget's Overall score with 12 GB. The RX 9070 XT gives 16 GB and the highest frame rates on three of the four charted models, but it supports fewer Starlight models locally.
Platform costs differ. The RTX 5060 Ti needs a single 8-pin connector and a 550 W supply per ASUS. The RTX 5070 and RX 9070 XT both come with 750 W recommendations from their makers, and the RTX 5070 uses a 16-pin connector. If your power supply is older, that can add a cost. Topaz Labs publishes its own list of supported GPUs, which is the place to check before buying. Market prices shift, so compare sellers before ordering.
What AI upscaling asks of a GPU#
AI upscaling runs a trained network on every frame of a video, so the work scales with the number of frames and the output size. A two-hour film at 24 frames per second has well over a hundred thousand frames, and each one passes through the model. That is why speed in frames per second matters, and why a card that is 30% faster saves hours on a long project.
Memory matters for a different reason. The model, the frame buffers and any extra processing stages must fit in VRAM together. If they do not, the software either refuses the model or falls back to slower paths. Topaz Labs lists 6 GB as the minimum and recommends 8 GB or more, and some of its newer models need more than the entry requirements. Puget's compatibility notes show what that means in practice for 12 GB and 16 GB cards.
Software support matters most of all. Each upscaling product chooses which GPU brands and which models it supports locally. Puget found the RX 9070 XT limited to one Starlight model for local processing, even though its raw speed on other models was the highest of the three. Check the software's own requirements page before you decide, and keep in mind that a new model release can change what a card supports.
How to choose#
- Check your upscaling models. Match them to Puget's per-model results before you choose a brand.
- Check memory. Topaz lists 6 GB as the minimum and recommends 8 GB or more, and some models need 8 GB. Newer models may need more.
- Check the GPU brand. AMD's RX 9070 XT supports fewer Starlight models locally, per Puget.
- Check your power supply. ASUS recommends 550 W and 750 W for the two NVIDIA cards, and PowerColor gives 750 W for the AMD card.
- Check the connector. The RTX 5070 uses a 16-pin connector. The other two use 8-pin connectors.
- Check the case. The makers list lengths of 229 to 304 mm, which may include the bracket. Compare with your case limit.
- Plan for your wider workload. If you also run language models or Stable Diffusion, see the 16 GB GPU guide and the VRAM explainer.
Common mistakes#
- Choosing by one model's result. The RX 9070 XT leads on three models and trails badly on another.
- Buying 12 GB for the newest models. Puget notes the RTX 5070 does not meet the requirements for some Starlight models.
- Assuming Puget tested the partner card. It tested reference or other-brand cards.
- Ignoring the power supply. Makers' recommendations range from 550 W to 750 W.
- Expecting a CPU upgrade to help. Puget says Topaz Video is mainly GPU-intensive.
Verdict#
Best overall ASUS Dual GeForce RTX 5060 Ti 16GB GDDR7 OCSee the details
The ASUS Dual GeForce RTX 5060 Ti 16GB is the best all-round choice. It has 16 GB of memory, compatibility with every Starlight model in Puget's test and the lowest power needs of the three. Choose the ASUS Dual GeForce RTX 5070 if you work with Artemis, Iris, Proteus or Proteus Natural and want the fastest NVIDIA card here. Choose the PowerColor Reaper RX 9070 XT only if your models are the ones where it leads and you do not need Proteus Natural or the wider Starlight range.
For related reading, see our GPU hub and the tensor cores explainer.
Long upscaling jobs keep the card hot for hours, so in warm Indian summers make sure the case airflow is good and the power supply suits your local 230 V mains.
Frequently asked questions#
How much VRAM do I need for AI video upscaling?
Topaz Labs lists 6 GB as the minimum and recommends 8 GB or more. Some models need 8 GB, and Puget found 12 GB insufficient for some Starlight models.
Is NVIDIA or AMD better for Topaz Video?
It depends on the model. Puget's results show the RX 9070 XT leading on several models and falling far behind on Proteus Natural 2X. Check the model you use most before you choose a vendor.
Do I need an expensive CPU for upscaling?
Puget says Topaz Video is mainly GPU-intensive, so a consumer CPU is still suitable. Spend the budget on the graphics card first, and pair it with enough system memory and fast storage for the video files.
Are these results for the exact cards listed?
No. Puget tested a reference RTX 5070, a PNY RTX 5060 Ti and a Sapphire RX 9070 XT. They show the chips and not the partner cards.
What power supply do I need?
ASUS recommends 550 W for the RTX 5060 Ti and 750 W for the RTX 5070. PowerColor gives 750 W as the minimum system power for its RX 9070 XT.
Can the same GPU run other AI work?
Yes, within their memory limits. NVIDIA and AMD software support differs, so see our CUDA vs ROCm explainer first. Upscaling tools may favour one vendor, which affects what else the card can run.
Which GPU is best for Topaz Video?
Puget Systems' Topaz Video results favour the RTX 5070 for speed among NVIDIA cards, while the 16 GB RTX 5060 Ti supports every Starlight model.
Is 16 GB of VRAM better than 12 GB for upscaling?
For compatibility, yes. Puget found the 12 GB RTX 5070 does not meet the requirements of some Starlight models, while the 16 GB RTX 5060 Ti does.
Sources & credits#
We have not tested these products ourselves. Specs come from the makers; benchmark figures come from the sources we name.
- Puget Systems, Topaz Video 1.6.1 Consumer GPU Performance Analysis (opens in a new tab)
- ASUS, Dual GeForce RTX 5070 12GB GDDR7 OC Edition tech specs (opens in a new tab)
- ASUS, Dual GeForce RTX 5060 Ti 16GB GDDR7 OC Edition tech specs (opens in a new tab)
- PowerColor, Reaper AMD Radeon RX 9070 XT 16GB GDDR6 (opens in a new tab)
- NVIDIA India, GeForce RTX 5070 family (opens in a new tab)
- NVIDIA India, GeForce RTX 5060 family (opens in a new tab)
- AMD, Radeon RX 9070 XT (opens in a new tab)
- Topaz Labs, Topaz Video system requirements (opens in a new tab)
Facts and figures in this article come from these sources. Articles are compiled from the makers' published specifications and the benchmarks named above, and checked by the NextAIGrid Editorial Team.
Disclaimer
This guide is for information only. Specifications and availability change, so check the retailer page before buying. Found an error? Tell us.
How was this buying guide put together?
It draws on 7 named sources: maker specification pages and published third-party benchmarks, listed in the article. We have not tested these products ourselves. Specs come from the makers; benchmark figures come from the sources we name. Specifications and sources were last checked on 17 November 2026. Warranty terms and availability differ by brand and seller in India, so check the maker's India page for the warranty period and buy from an authorised seller. Read how we research and our editorial policy.
Spotted an error? Tell us. Confirmed fixes are listed on the corrections page.